newmicros.net

Home > Error Codes > Nortel Cs1000 Error Codes

Nortel Cs1000 Error Codes

Contents

PWR: Power and System Monitor . . . . . . . . . . . . Seems odd b/c I have a few other TNs on different cards giving me the same problem. SCH0122 Loop out-of-range (0-159). Module: NARS. weblink

Action: Enter absolute value: 0, 5, 10 or 15. Terminal Already Exists Error - SCH0127 rilhouse (TechnicalUser) (OP) 12 Nov 06 14:31 The SCH code is coming from the terminal in OTM which I assume is the switch talking?Could some Check high-speed link cable. Terminal Already Exists Error - SCH0127 rilhouse (TechnicalUser) (OP) 9 Nov 06 15:00 I was just trying to add a basic 2008.

Nortel Cs1000 Error Codes

AUTH: Authorization Code (LD 88) . . . . . . . . . . . Valid only for ACD Package D services. Procedure: GET_TRUNK. SCH0150 Wrong number of input fields for prompt CUST.

Action: Install NI-2 CBC package. CCR: Customer Controlled Routing . . . . . . . . . . SCH0169 Illegal digit in DN. Cannot find the transaction number for the system.

Action: Check data and re-enter command. Module: GLOB4. SCH0171 Step route number out-of-range (0-31). MSR0022 MSR0025 Peripheral signaling pack already enabled.

Route is not an outgoing route or an AWR route. SCH0160 Wrong number of input fields for prompt ROUT. Procedure: INITIATE_B_CH. The Priority Agent Package (PRI) is not equipped.

Nortel Error Codes

Module: NARS. The trace information is output to the all system terminals designated in LD 17 as ADAN = TTY and USER = MTC. Nortel Cs1000 Error Codes Action: Remove the high-speed link in software, then redefine it. Nortel Cs1000 Commands SCH0107 There are no available busy lamp fields.

This document is issued to include updates and changes required for X11 Release 25.0x June 1999 Standard 6.00. http://newmicros.net/error-codes/dresser-wayne-error-codes.html PRA_EOD_FLAG is set, the first digit is 0 but digit translation is not.EXACT#_KNOWN. MGC n is faulty. Module: ISDN.

Once loaded, ACD configuration data is sent to the auxiliary processor from the SL-1 through the high-speed link. SCH0114 An attempt to define the CFMS class of service in LD 14 for a digital trunk on CDT/CSDT12 loop without CISFW=MFS. NPR: Network and Peripheral Equipment Diagnostic (LD 32) . . . . . . . . . . . . . . . . . . . . . . . check over here Module: ISDN.

Procedure: OUTG_CALL_INIT. Invalid character entered. Action: Check baud rates of the SDI for the high-speed link and high-speed link port on the auxiliary processor.

Pack can now be serviced.

Module: GLOB4. Auxiliary processor has difficulty processing the messages. Module: DIGPR. A Ring Again (RGA) call is in the TOF queue.

The SL-1 has run out of call registers. ADD is only available when the ACD Auxiliary Data System (ACD-ADS) is equipped. NWS: Network and Signaling Diagnostic (LD 30) . . . . . . . . . . . . . . . . . . . . . . . . this content Procedure: GET_TRUNK.

SCH0191 Directory number already exists. Multigroup control specified is out-of-range. 0 to 1 is allowed. This Target ID does not exist in the table specified. When other errors are logged, the ALARM indicator will turn off only when the log for major or minor errors is cleared from the KX-TDA Maintenance Console.In other words, the ALARM

Procedure: TRUNKTER.